|
1.4 Air-Con & Ventilation System
1.4 空調及通風系統
|
Refer to hot-water system
參照熱水系統
|
|
|
Centrifugal Air Duct
Fan/Centrifugal Blower
離心式通風機/離心式鼓風機
|
Common ventilation,
dust content in air ≯150mg/m3, temperature ≤60℃, no corrosion. Body shell of
fan use galvanized steel plate; its thickness must stand the weight of motor
and other drive equipment. Examine and repair doors are at both sides. The
fan is centrifugal fan; the air inlet of impeller must be arc to insure that
the transition is fluent between air inlet and Venturi tube. Antisepsis and
had passed the test of dynamic balance and static balance. The strap must
selec according to 1.5 times of drive power, trap can be adjust in locale to
make the test of balance. The axis is permanent airproof, and can be
lubricated. Motor shall be concert with the load of fan,380V, IP54,
insulation grade F. Must show its working noise (DB(A)).Fan must be with absorber,
and show its numerical value of absorb. Each fan shall be provided with the
isolation switch and connection point with BAS system. The spring shock
absorber shall be applied as the centrifugal fan above 6#; the rubber pad
shock absorber shall be applied as the centrifugal below 6#. The inlet and
outlet of the fan shall be provided with flexible joints
普通通風、氣流含塵量≯150mg/m3、溫度≤60℃，無腐蝕性。外殼應采取鍍鋅鋼板，鋼板厚度應足以承受驅動機構和電機的重量；風機兩側應設有檢修門，風機類型應為離心風機，葉輪進口文丘里管截面應成圓弧形確保與風機進口文丘里管過渡順暢；風機軸應經過熱處理達到硬度HB370等級；表面應進行防腐處理，并連同葉輪一起進行動靜平衡測試；皮帶應按照驅動功率的150%選型，且可以調節以便進行現場的系統平衡；軸承應是永久密封，并可潤滑；電機應與風機負載緊密配合，380V，IP54，絕緣等級F；應明確標明風機運行噪音值（dB(A)）；應配有減振器，并標明減振量。每一風機應帶有就地控制開關，并可連接信號至BAS系統。6#以上的離心風機應采用彈簧減震器，6#以下的離心風機可采用橡膠墊減震器，風機進出口應設有柔性接頭
|
WOLTER, TWIN-CITY,
Greenheck, Kruger
沃特、雙城、格林瀚克、科祿格、
|
|
AHU(Air Handling
Unit with Heat Recovery) & PAU(Pre-Cooling Air Handling Unit)
空氣處理機組/預冷空調箱
|
Unit
construction and unit assembly complies with DIN EN 1886 and VDI 6022. The
thickness of the AHU panels is required more than 70mm and the specific
volume of the insulation material are required more than 55kg/m3. Insulation
material is required to use mineral fibre. The flame resistance shall be
reached the A. Contractor shall supply, install, testing, and service in
accordance strictly with drawings, criterion and specification
施工和裝配按照德國標準DINEN1886和VDI6022，AHU Panels厚度大于70mm，絕熱材料容重大于55kg/m3，絕熱材料選用礦棉纖維，A級阻燃。承包商應嚴格按照圖紙、規范及本項目技術文件供應、安裝、調試及服務
|
AL-KO, Robatherm,
Carrier, Klingenburg (heat recovery)
愛科、羅百特、開利
克林根堡（用于能量回收段）
|
|
Constant temp &
humidity air conditioner
機房精密空調
|
Precision
air-conditioning for IT& computer room, Indoor units shall be provided
with the isolation switch and connection point with BAS system. Contractor shall
provide all air-cons intact and effective documents and test records in
accordance with Specification.
用于空調和IT房間，每一室內機應帶有就地控制開關，并可連接信號至BAS系統。所有空調設備需要提供技術規范說明書中所有完整有效的資料和測試記錄
|
Caros, Emerson,
HAIRF/HiRef, Stulz
卡洛斯、艾默生、海瑞弗、史圖斯
|
|
Outdoor split air
conditioners
分體空調
|
Used for cooling for
general offices in summer. In order to correctly install the split air
conditioner, the Contractor must provide all necessary units, materials and
cabling. The protection class of outdoor unit must be suitable for outdoor
use and shall be no lower than IP55, 220V. All materials to be used for
silence and heat insulation must conform to the latest requirements of local
fire department. The appropriate units shall be provided according to the
requirements specified in the drawing and equipment list to satisfy maximum
cooling amount in summer. The air conditioner shall have single cooling
functions according to the design requirements; the coolant of air
conditioning shall be no harm to environmental protection. All outdoor units
shall be installed on the channel-steel foundation and have protection for
rain-proof. The units shall include compressor, condenser coil, fan, engine,
access opening of control box and control desk control panel for use and
maintenance. The position and layout of condenser must be free from space
constraint and avoid to circuit for hot air. Cabling from indoor units to the
control panels shall also be the contractor’s works scope, the operation
signal and disturbance signal of each outdoor air-conditioner must have the
function accessing the BAS. Indoor units shall be provided with the isolation
switch and connection point with BAS system
普通辦公室夏季制冷，為了正確地安裝分體式空調機組，承包商須供應所有必需的裝置，材料及配線。室外機組防護等級必須適合室外使用，且不得低于IP55，220V。所有用作消音及保溫的材料必須符合當?shù)叵谰值淖钚乱蟆ｍ毎凑請D紙設備表內所示要求提供合適的機組設備以滿足夏季的最大冷凍量的要求。空調器應按設計要求具備單冷功能，冷媒必須對環境無害。所有室外機組應裝配在整體型鋼基礎上并有防雨措施。機組應包括壓縮機、冷凝盤管、風扇、發動機、控制箱檢查口和使用維修控制面板。冷凝器的位置和布置必須避免空間限制和熱空氣的二次流通。包括室內機與控制器間的電線，每一室外機組的狀態信號及故障信號具備可接入BAS系統功能；每一室內機應帶有就地控制開關，并可連接信號至BAS系統
|
DAIKIN, YORK,
MITSUBISH, TRANE, CARRIER
大金、約克、三菱、特靈、開利
National famous brand: Haier, Gree, Midea
海爾、格力、美的
|
|
Multi-split Air
Conditioning System
空調多聯機
|
|
DAKIN, YORK,
MITSUBISH
大金、約克、三菱
National famous brand: Haier, Gree, Midea
海爾、格力、美的
|
|
Fan coil
風機盤管
|
|
DAIKIN, YORK,
MITSUBISH
大金、約克、三菱
National famous brand: Haier, Gree, Midea
海爾、格力、美的
|
|
Air duct
heater/Cooler
風管加熱器/冷卻器
|
|
Trox, Halton,
Zehnder,
妥思、霍爾頓、森德
|
|
Noise
silencer/Muffler
消音器
|
Common
ventilation, dust content in air ≯150mg/m3, air supply temperature in winter
23℃, outdoor natural wind in summer, no corrosion. Including the mufflers for
square and round pipes. The shell shall be made by the galvanized steel sheet
and the joints shall be sealed. The over-sized muffler shell shall be fixed
with strips. The silent pad shall be made by the non-textile glass fiber
material. Before formal installation, the contractor shall submit specific
muffler selection and technical parameter sheets. The data in the technical
parameter sheet shall cover each-muffler manufacturer, brand, model, size,
weight, quantity of silent pad, resistance loss and noise parameter. The
above parameters shall be given based on the muffler flow and length
appointed in the drawings
普通通風，氣流含塵量≯150mg/m3，送風溫度冬季為23℃，夏季為室外自然風，氣流無腐蝕性。外形為方形或圓形。外殼鍍鋅鋼板制作，接縫處做密封處理，超大尺寸外殼需做加固處理，消聲片由非織物玻璃纖維材料制作。正式安裝前，承包商應提交詳細的消聲器選型及技術參數表，數據應包含每臺消聲器的制造商、品牌、型號、尺寸、重量、每臺消聲器的消聲片數量、阻力損失、消聲參數等，這些參數應基于圖紙給定的消聲器流量及長度
|
Trox, Halton, shinelong
妥思、霍爾頓、顯隆
|
|
All kinds
Damper(incl. electrical damper) grille
各種風閥(包括電動風閥)
|
General
ventilation system, dust content in air ≯150mg/m3, temperature ≤60℃, humidity ＞85%. De-smoke system, in case of fire: temperature
≤280℃; normal: dust
content in air ≯150mg/m3,
temperature ≤60℃,
humidity ＞85%. The
dampers must opposed multi-blade dampers. Case, shall not produce vibration
or sound. The air leakage volume is not higher than 5% when the dampers
closed. There is excellent seal between body and shaft. Fire damper shall
conform to the requirements of local fire department and relevant Chinese
regulation or code. Fire damper shall also be provided with one fusible sheet
with operating temperature of 70℃. In case
the air temperature is higher than 70℃, the fire damper shall be closed. Besides it can only
be reset manually. All dampers are made by carbon steel
普通通風系統，氣流含塵量≯150mg/m3，溫度≤60℃，排風濕度＞85%；排煙系統：火災溫度≤280℃，平時：氣流含塵量≯150mg/m3，溫度≤60℃，排風濕度＞85%。風量調節閥須為多葉對開葉片型，所有調節閥在任何情況下，都不能產生震動或聲響，調節閥緊閉時其漏風程度不能大于5%。調節閥體和轉軸須有良好密封；防火閥須符合當?shù)叵谰旨坝嘘P(guān)中國國家標，防火閥應同時配有一易熔片，其操作溫度為70℃，當排經的煙氣溫度大于70℃時，將防火閥關閉。并只能以手動復位。所有的風閥均由碳鋼制作
|
Trox, Halton, shinelong
妥思、霍爾頓、顯隆
Electric driver: BELIMO, SIEMENS, HONEYWELL, Trox
風閥電動驅動器：博力謀、西門子、霍尼韋爾、妥思
|
|
Constant Air Volume
Regulator(CAV)
定風量調節器
|
The
constant air volume regulator shall be the pressure-independent type. The
automatic mechanical regulator with the air volume through the constant air
volume regulator can strictly supply or exhaust air according to the dial
scale without impact of pipe static pressure and air volume change. The valve
body structure of the constant air volume regulator shall be the single-
plate throttle and can automatically adjust the opening of the valve position
according to the static pressure before the valve, so the constant air volume
can be ensured. The square-shape constant air volume regulator shall be
equipped with flanges on both ends. The both ends of the round-shape constant
air volume regulator shall be the sockets with actuators. The constant air
volume regulator can work at the static pipe pressure of 50-1000Pa and not be
limited by the installation position which can be horizontal or vertical. The
air volume calibration of each-set end unit shall be carried out in plant and
the accuracy shall be ensured. It is made by carbon steel hot- galvanized
定風量調節器應是壓力無關型，機械式自動調節裝置，經過定風量調節器的風量，可嚴格按照刻度盤標定的風量送風或排風，不受管道干管靜壓以及風量變化的影響。其閥體結構應為單閥板節流形式，并根據閥前靜壓的變化自動調整閥位的開度，從而保證送風量的恒定。方形的兩端應帶法蘭，圓形定的兩端為插接口，并可附帶執行器。定風量調節器可在管道靜壓壓差50至1000Pa范圍內正常工作，并且不受安裝位置的限制，可水平或垂直安裝。每臺末端裝置的風量標定工作應在工廠進行，并保證標定的準確性，同時應能在現場進行額定風量的二次標定，以適應項目情況的變化，由熱鍍鋅材料制作
|
Trox, Halton, shinelong
妥思、霍爾頓、顯隆
Electric driver: BELIMO, SIEMENS, HONEYWELL
風閥電動驅動器：博力謀、西門子、霍尼韋爾
|
|
G.I. steel board air
duct with accessory
鍍鋅鐵皮風管
|
For
the rectangle air duct which is ≥800mm, the support bracket inside the pipe shall
be used for reinforcement (see the assembly sequence). Combination flange
rectangle air duct which is 1250mm≤ air duct edge length (A) ≤2250mm, the rib
line and inner-duct support shall be used and the inner support part is 1
piece. >2250mm, 2 pieces。All the ducts for air supply and
return, air exhaust and exhaust smoke duct shall be generally made of
galvanized sheets. The fabrication of all ducts sheets shall conform to
Unless
additional specified, all the ducts shall be made of galvanized steel sheet, Ducts
thickness shall conform to the minimum thickness as specified by the above
standard. Galvanized steel sheets shall meet the requirements of
GB50243-2002. Rubber seal joint gaskets or suitable adhesive shall be used as
air-tight seal for all flange joints
對邊長≥800mm的矩形風管，采用管內支撐架方式加固，對于1250mm≤風管邊長 (A) ≤2250mm的風管，采用楞線和管內支撐加固方式，管內支撐為1個，大于2250，2個。所有一般空調送回風、排風和排煙風管道由鍍鋅鋼板制成。所有金屬板的風管道的制作須按照中國標準GB50243—2002。除特別說明外，所有風管須為鍍鋅鋼板風管，板厚須同時符合上述標準內所規定的最小厚度而制造。鍍鋅鋼板能滿足GB50243-2002之板材要求，所有法蘭接駁位須采用橡膠密封接合墊片或合適的膠粘劑作為氣密封
|
China national
standard high quality products: WuSteel, AnSteel, BaoSteel, BenSteel，TongSteel
國標優質產品：武鋼、鞍鋼、寶鋼、本鋼、通鋼
|
|
Diffuser (Incl. Round
diffuser with air volume adjust, Displacement air port, Swirl diffuser)
風口（包括：帶風量調節圓形散流器、置換風口、旋流風口）
|
Round
exhausts and supply diffuser with air volume adjustment: It shall be made of
prefabricated aluminum alloy, corrosion by oxidation treatment; surface
painted by the architect requires recognition of color. Center separate
diffuser blades to be equipped with square or round neck. Each diffuser shall
be equipped with a steel plate made of aluminum or more leaf off the air flow
control valve, shall be painted black blade hidden by a built-in spacious
style adjustable rod for adjustment
帶風量調節圓形排風和進風散流器：由預制鋁合金材料制作，經氧化防蝕處理后，表面按建筑師要求涂上認可的顏色。中心葉片分離式散流器須配有方形或圓形頸，每個散流器須配有一個由鋁合金或鋼板制成的對開多葉式風量調節閥，葉片須涂上黑色由一內置隱敝式調校桿作調校
|
Trox, Halton, shinelong
妥思、霍爾頓、顯隆
|
|
Displacement air
port
置換風口
|
Displacement
air port: The shell and the support grid shall be made by galvanized plate
which can be sprayed as RAL standard. The noise parameter must be the sound
power level tested in the standard echo chamber. The supplier must provide
the selection reports based on the actual project condition
置換風口：外殼和支撐格柵由鍍鋅鋼板制成，可根據RAL標準進行噴涂。噪聲參數必須在標準回響室內測得的聲功率噪聲，供貨廠家必須能提供針對本項目實際情況得出的選型報告
|
Trox, Halton, shinelong
妥思、霍爾頓、顯隆
|
|
Diffuser
散流器
|
Swirl
exhaust and supply diffuser with air volume adjustment: Swirl vanes can be
independently adjusted to meet the different swirl air supply in different
rooms. The panel shall be made of galvanized steel sheet and the surface shall
be painted with powder as the project required. The swirl vane material shall
be polystyrene. The color shall be white or black. The supplier must provide
the selection reports based on the actual project condition
帶風量調節旋流排風和進風散流器：旋流葉片具有單個可調節特點，以滿足不同房間的不同旋流送風特點。面板材料為鍍鋅鋼板，表面需根據工程要求粉末噴涂顏色，旋流葉片材料為聚苯乙烯，顏色為白色或黑色。噪聲參數必須在標準回響室內測得的聲功率噪聲，供貨廠家必須能提供針對本項目實際情況得出的選型報告
|
Trox, Halton, shinelong
妥思、霍爾頓、顯隆
|
|
Door Hot Air Curtain
風幕
|
Wall
mounted type heater, Horizontal Flow Q: refer to drawings, water temperature 90/40℃, noise level≦67dB(A)
頂吹大門熱風幕，水平安裝，配中間出風噴嘴，流量見圖紙，水溫90/40℃，噪音≦67.0dB(A)
|
Zehnder, Kampmann,
TTL
森德、卡普曼、TTL
|
|
Wall Mounted Type
Heater
墻裝加熱器
|
Horizontal
installation, Flow Q: refer to drawings, water temperature 90/40℃, noise level≦67dB(A) ), indoor temperature:
19℃
水平安裝，流量見圖紙，水溫90/40℃，噪音≦67.0dB(A)，室溫19℃
|
Trox, Halton,
Zehnder,
妥思、霍爾頓、森德
|
|
Warm air blower
暖風機
|
Flow
Q: refer to drawings, water temperature 90/40℃, noise level≦61dB(A),
indoor temperature: 10℃
流量見圖紙，水溫90/40℃，噪音≦61.0dB(A)
，室溫10℃
|
Trox, Halton,
Zehnder,
妥思、霍爾頓、森德
|
|
Exhaust Heads
風帽
|
Installed
the end of upper wind outlet dust, round type, cylinder type, square type,
size see construction drawings, and vertical installation normally. It has
fixed mechanical strength, can resist
violent typhoon
安裝于風道上出口終端，有圓傘形，筒形和方形，尺寸按照施工圖，垂直安裝，具有一定機械強度，可抵抗強臺風
|
IMOS,
BeijingHangtian Taizhou pipe equipment CO.LTD
IMOS、北京航天、臺州管業
|
|
Supports
支吊架
|
Meet
drawing and specification
按照圖紙和規范
|
Golkin, Shanghai
Xinqi, Walraven
固多金、上海新奇、
沃雷文
|
|
Anchor Bolt
錨栓
|
|
Hilti, Simpson, Fisher
喜利得、辛普森、慧魚
|
|
Fire-stopping
防火封堵
|
Refer
to hot-water system
參照熱水系統
|
STI, 3M, Hilti
STI、3M、喜利得
|
|
Strainer
水過濾器
|
Refer
to hot-water system
參照熱水系統
|
Watts, Danfoss, THT
沃茨、丹佛斯、津濱瓦特斯
|
|
Pressure Gauge,
Temperature Gauge
壓力表、溫度計
|
Range
and precision, see bidding document Chapter 7
量程、精度參見招標文件第七章規范
|
GF, Honeywell,
Dwyer,
喬治.費歇爾、霍尼韋爾、德維爾
|
|
Insulation
橡塑保溫
|
Meet
drawing and specification
按照圖紙和規范
|
Armacell,3M,Yingsheng
阿樂斯、3M、贏勝,
|
|
Rock Wool insulation
保溫巖棉
|
Meet
drawing and specification
按照圖紙和規范
|
Saint-Gobain, Owens Corning,
CSR
圣戈班、歐文斯科寧、西斯?fàn)?
|
|
Shock absorber 減震器
|
The
spring shock absorber shall be applied as the centrifugal fan above 6#, the
rubber pad shock absorber shall be applied as the centrifugal below 6#. Meet
design and equipment manufacturer installation instruction at the same time
6#以上的離心風機應采用彈簧減震器，6#以下的離心風機可采用橡膠墊減震器；同時符合設計和設備制造商按照說明
|
Mason, EHASE-FLEX,
JSC, Liaoning Tongze
梅森、通力、兆山辰、遼寧同澤
|
|
Flexible Joints
柔性接頭
|
Flexible
duct shall be made of flexible metallic bellows using stainless steel,
aluminum, galvanized steel or aluminum steel. Flexible joint shall meet the
requirement of air-tightness and be suitable for specified air pressure and
temperature conditions. Relevant material shall be fire-proofing material and
shall conform to the regulations of local fire department
柔性通風管道應由不銹鋼、鋁、鍍鋅或鋁鋼所制成的柔性金屬波紋管，柔性軟接頭的材料須滿足氣密性要求，適用于指定的風壓和溫度條件。有關材料須為防火材料，防火程度須符合當?shù)叵谰忠?
|
